1 - Adattamento dei piroli di violino - Finitura della conicità dell’asta
⬇️⬇️ (English translation below the Italian text) ⬇️⬇️
00:05 - Adattamento dei piroli - parte prima - Finitura della conicità dell’asta
00:11 - Utilizzare un tempera-piroli con conicità esattamente corrispondente a quella dell’alesatore che si utilizzerà per l’adattamento alla cassetta piroli (conicità di 1:30). Con un coltello incidere la fine dell’asta sotto al collare per evitare scheggiature. Applicare la forza di rotazione in modo molto uniforme, girando il pirolo lentamente e con la minore pressione possibile, per evitare di disassare il cono rispetto al centro dell’asta e alla testa del pirolo. A questo proposito verificare frequentemente che il gradino che si forma in corrispondenza del limite della lama del temperino sia uniforme per tutta la circonferenza. Nelle fasi iniziali può essere utile inumidire il legno con acqua per renderlo più plastico ed evitare strappi e scheggiature. Arrivati a 2 o 3 mm dal collare, lasciare asciugare bene il legno e finire la conicità senza bagnarlo (importante!), per evitare che la conicità si deformi in seguito al ritiro del legno causato dalla asciugatura. Lucidare il cono con cartavetro consumata Micromesh grit 2400, seguita da una lucidatura con cera d’api applicata con uno straccetto di cotone.
08:29 - Lasciare asciugare bene il legno prima di procedere con la finitura dell’asta. Proseguire senza più bagnare il legno, per evitare che il ritiro causato dall’asciugatura deformi la conicità definitiva.
11:29 - Lucidare l’asta con cartavetro Micromesh 2400 consumata, facendo attenzione a non applicare troppa pressione per non modificare la conicità. Finire la lucidatura strofinando bene con cera d’api applicata su uno straccetto di cotone.
English translation
00:05 - Pegs fitting- part one - Finishing of the taper of the shaft
00:11 - Use a peg shaper with a taper exactly corresponding to that of the reamer that will be used to adapt to the pegbox (taper of 1:30). With a knife cut the end of the shaft under the collar to avoid chipping. Apply the rotation force very evenly, turning the peg slowly and with the least possible pressure, to avoid misaligning the cone with respect to the center of the shaft and the head of the peg. In this regard, frequently check that the step that forms at the edge of the blade is uniform along the entire circumference. In the initial stages it can be useful to moisten the wood with water to make it more plastic and avoid tearing and chipping. When you reach 2 or 3 mm from the collar, allow the wood to dry well and finish the taper without wetting it (important!), to prevent the taper from deforming due to the shrinkage of the wood caused by drying. Polish the cone with worn Micromesh grit 2400 sandpaper, followed by polishing with beeswax applied with a cotton rag.
08:29 - Allow the wood to dry thoroughly before proceeding with the finishing of the shaft. Continue without wetting the wood, to avoid that the shrinkage caused by drying deforms the final taper.
11:29 - Polish the shaft with worn Micromesh 2400 sandpaper, taking care not to apply too much pressure to avoid modifying the taper. Finish the polishing by rubbing well with beeswax applied to a cotton rag.
Index of videos - English:
Italiano:
1 view
1436
440
6 months ago 00:30:11 1
НАШЛИ ЛУЧШИЙ УТЕПЛИТЕЛЬ ДЛЯ ДОМА - ТЕСТ ВСЕХ УТЕПЛИТЕЛЕЙ НА РЫНКЕ
6 months ago 00:14:57 1
ОБРАЩЕНИЕ к педагогам и не только
6 months ago 01:00:43 1
Распаковка посылок из Японии в Нижегородском магазине Dendy
6 months ago 00:13:53 1
Новости игр! Cyberpunk 2077, Escape from Tarkov, Call of Duty, Helldivers 2, Suicide Squad
6 months ago 00:22:34 1
Выпуск 7. МБУ “Музей космонавта Георгия Берегового“ администрации г. Енакиево. Часть 1.
6 months ago 00:02:22 2
PUBG | Patch Report #29.1 - New Rondo Feature Destructible Terrain, Ducati Collaboration and MORE
6 months ago 00:09:37 1
Зачем? Старт съемок Матрицы 5/Полная перезагрузка или полная ж**а?
6 months ago 02:39:19 2
Старцы - Загадка вымершей цивилизации Антарктиды
6 months ago 00:02:42 1
David Guetta & OneRepublic - I Don’t Wanna Wait (Live performance at Ultra Music Festival 2024)
6 months ago 01:04:57 1
Кадровая политика университета: работа мечты?
6 months ago 00:09:07 1
Наша задача — сформулировать повестку.
6 months ago 00:40:02 1
Город-призрак Цхалтубо. Как живут люди в городе брошенных санаториев СССР
6 months ago 00:03:22 1
Prix de la trahison de la France : 10 à 15 millions...!
6 months ago 00:15:43 1
’Poppin’ Love 心动预告’ Dance Practice Behind | WayV Showcase Tour ’On My Youth’ Behind Ep 1